Nextar NP-610X Bedienungsanleitung

NP-610X X86 CISC-based Operator Interface Terminal with 10.4” Flat Panel Display User’s Manual

10 2.2.1 Power Requirements Power The NP-610X can be powered by DC power only. The specified voltage range is +21 to 25 Volts DC. This insures com

11 clockwise until it’s tight. Connect positive DC line to the ‘+24V’ terminal and the DC ground to the ‘GND‘ terminal. FUSE Replacement: The fuse us

12 2.2.4 Safety Guidelines This section presents recommended installation practices, and procedures. Since no two applications are identical, these r

13  The ICS 3-304.81 Safety Recommendations are reproduced by permission of the National Electrical Manufacturers Association from NEMA ICS 3-304

14 2.3.1 Connector COM 1 [RS232] 2.3.2 Connector COM2[RS232], COM3[RS485] and COM3[RS232]

15 COM3 [RS-485] connect RS-485 2 wire Device NP-610X COM1 [RS-485] 9P D-SUB Female RS-485 2 wire Device 4 Data+ Data+ 5 Data- Data- 1

16 2.4 CE Requirements EU directives that apply to the NP-610X Series:  EMC Directive (89/336/EEC, 92/31/EEC, 93/68/EEC) electromagnetic emissions

17 Dimensions of NP-610X Cutout dimensions: NP-610X: 352mm [13.86”] W x 279mm [10.98”] H

18

19 Chapter 3 Windows CE.NET 3.1 Introduction The NP-610X series operator interface terminal is designed to serve on the Windows CE platform. Windows

2 Copyright... 3 Safety Instructions.

20 3.2.2 System Settings NP-610X provides an integrated utility for users to make basic setting of the machine. Step 1. Tap the “cecp” icon f

21 Touch Screen settings The touch screen calibration can be executed from the Control Panel. Step 1. Launch the System Settings Control Panel.

22 “LCD Settings” page of the cecp provides the function to turn off the LCD backlight, and thus elongates the period of service. For example, if the

23 MAC address The MAC address page the block shows the network MAC address. Save Tap the Save registry button, would save the registry data to

24 Contrast Adjust the LCD contrast. 3.2.3 Hard Disk The Hard Disk serves as a small capacity hard disk. You can store your data and a

25 make a shortcut and copy it to "Hard Disk\StartUp". A shortcut can execute a program with Parameters. Follow the following procedure to

26 To create a new Remote Desktop Connection 1. Open Remote Desktop Connection. 2. In Computer, type the computer name for your computer running W

27 3.3 NP-610X Networking 3.3.1 Networking via Ethernet The NP-610X is equipped with a 10/100Base-T Ethernet controller. To utilize it, change the d

28 6 Use the cecp utility “Save registry” to save this changed. 3.3.3 Web browser The NP-610X built-in Windows CE OS includes Microsoft Pocket Inte

29 3.4 Application program development The NP-610X is bundled with built-in Windows CE operating system. In real applications users need to execute v

3 Copyright This document is copyrighted January l, 2008, by IVC Displays, Inc. All rights are reserved. IVC Displays, Inc. reserved the right to mak

30 3.5 Print NP-610X support PCL language printer. You can connect a PCL printer at USB Host port or via Network connect to a shared printer. From In

31 Desktop PC shares the printer.

32

4 Safety Instructions Overview This section states the safety instructions, which must be followed when installing, operating and servicing the NP-61

5 Chapter 1 Introduction 1.1 Introduction The MT612X is a miniature and compact platform that has excellent system performance and function. The

6 • On-board 512MB DDR-400MHz SDRAM • 44-pin IDE Interface (Disk-On-Module) • 3 serial ports (2-RS232, 1-RS485 2W/4W) • 2 USB ports full-speed po

7 • Resolution: continuous • Light transmission: above 80% • Life: 1 million activation minimal Environmental Specifications • Operating tempera

8 Chapter 2 Installation Instructions 2.1 Mounting Instructions 2.1.1 Location Considerations Care should be taken when locating equipment behind t

9 2.1.3 Environmental Considerations  The NP-610X are to be used indoors as built in displays. Make sure that the displays are installed correctly